![]() ![]() When a high level of RF continues to be applied to a trap or coil that has not sufficiently cooled, irreparable damage will occur. IMPORTANT: Running a continuous carrier power mode (FT8, AM, RTTY) on any band on which the antenna has a trap, will create an accumulation of heat inside the trap windings, depending upon power level and keying cycle times. Completely normal operations are possible at these modestly elevated SWR levels, using a tuner when required by the transceiver or amplifier. Keep in mind that a 1.5:1 SWR represents only 4% reflected power and a 2:1 SWR represents only about 10% reflected power. Even so, the antenna is usable at full mode rated power on all bands. This approach results in an elevated SWR minimum on 17 and 40 meters, between 1.5:1 to 2:1 or above. However, for operations on both 80 and 40 meters, then it is best to favor 80 meters by setting resonance to the desired 80 meter frequency with the resonator whip length, and adjusting the SWR to around 1.5:1 with a coil tap point at the appropriate spot above the middle turns of the DXE-VMN-1 coil. Optimization of the SWR only for 40 meters, with the DXE-VMN-1 coil tap point only a couple of turns from the bottom, will typically result in a lower minimum SWR on 17 meters. The frequency of lowest SWR on 17 meters is affected by the presence and tuning of the DXE-VMN-1 Vertical Matching Network, which is required for 40 and 80 meter impedance matching on the Hustler BTV series antennas that are installed with many radials for high efficiency operations. Adjustment of tuning rods will likely be required. Mount them 180 degrees apart from each other.īase View of 4-BTV with DXE-AOKC-17M and DXE-VMN-1 Your BTV can have both the DXE-AOKC-17M - 17 Meter Add-On Kit and the DXE-AOKB-12M - 12 Meter Add-On Kit installed at the same time. Highly recommended for use during assembly is Jet Lube SS-30 Pure Copper Anti-Seize JTL-12555 for all aluminum and stainless steel hardware and joints. Scotch-Brite® Pad for cleaning the BTV tubing for the 17 Meter element clamp connections.Two 14.375 inch long Tuning Rods with Corona Balls. ![]() Spring loaded End Insulator to keep the 17 Meter element wire snug.Four Stainless Steel Band Clamps with Threaded Studs.Pre-assembled 17 Meter element wire with #10 soldered ring terminals.This updated kit features a unique combination of aluminum, stainless steel and poly-resin brackets, tuning rods, a large heavy-gauge aluminum wire coil, PTFE insulated wire, stainless steel clamps and hardware, in an easy to assemble project with all of the required parts included: SWR may be optimized for CW and digital or SSB segments by careful trap sleeve tuning adjustments on the BTV. After the DXE-AOKC-17M is installed and tuned, any required shift of the usable SWR frequency ranges on those bands is accomplished by trap sleeve repositioning on the respective band trap. Installation of the DXE-AOKC-17M can have the effect of narrowing the SWR bandwidth of 20, 15 and 10 meters, a reasonable trade-off for adding the extra band. The DXE-AOKC-17M 17 Meter Add-On Kit is rated at 1,500 watts PEP SSB, 1,000 watts CW and is conservatively rated for RF power handling of 375 watts RTTY and Digital modes including FT8, at antenna SWR of 2:1 and below. Therefore, precise adjustment of the tuning rods is typically not critical. Even if the minimum SWR is over 100 kHz away from the 17 meter band, the resulting SWR in the band is typically very low. The minimum SWR will vary from as low as 1.2:1 to over 1.6:1, depending upon several variables. The DXE-AOKC-17M 17 Meter Add-On Kit has a very wide SWR bandwidth. This kit will operate across the entire 17 meter band, 18.068 through 18.168 MHz. It's easy to add 17 meter band coverage to the Hustler BTV series vertical antennas, without giving up any existing band coverage! ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |